Xantech D5KP User Manual

- 1 - INSTALLATION INSTRUCTIONS D5KP DIGI-5 DDS Digital Distribution System OLED Keypad for 1-source and 4-source systems

- 10 - Installation The D5KP is designed to mount in a standard single-gang rough-in box (J Box). Typical mounting height is 56-60” from the fl

- 11 - 3. Connections ZONE OUT – D5RH The ‘ZONE OUT’ RJ-45 connector’s interface with D5KP Amplified Keypad through CAT-5 cables wired to the

- 12 - ZONE OUT – D5SH, D5SH4 The ‘ZONE OUT’ RJ-45 connector’s interface with D5KP Amplified Keypad through CAT-5 cables wired to the T-568A S

- 13 - Auxiliary Power Connector (AUX POWER OUT) – D5RH and D5SH, D5SH4 For wire runs over 150’, it is recommended to run an additional 16 AWG/

- 14 - 291D SERIESD5KPInternal Wire Colors White IR OUT Black GND Red +12VD5IP Source Input Wall Plate Interconnecting between t

- 15 - Internal IR Receiver The internal IR receiver is located beneath the ‘X’ button. The internal IR receiver can receive and respond to com

- 16 - D5KP Speaker Connections The D5RH and D5SH, D5SH4 routes digital audio to connected D5KP Amplifier Keypad where the audio is then amplif

- 17 - 4. D5KP Installer Setup The D5KP Installer Setup is defined into two categories, “User Parameters” and “Setup Parameters”. User Parame

- 18 - USER PARAMETERS BASS The “bass” control allows the sound to be adjusted on the lower frequency range. Using the volume bar as an indica

- 19 - USER PARAMETERS (continued) WHOLE HOUSE MUSIC (WHM) Whole House Music mode links all zones to share source selection functionality so t

- 2 - Safety Information CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.

- 20 - SETUP PARAMETERS SOURCE NAMES The source names can be changed. Select the source name that is to be changed and press the “X” button. B

- 21 - SETUP PARAMETERS (continued) INTERNAL IR ENABLE (IR INT) This setting allows the built-on IR Receiver to be disabled if desired. This f

- 22 - 5. Troubleshooting Symptom Possible Cause Solution D5KP does not power up 1. RJ-45 plug crimped incorrectly; or wiring pin-out of RJ

- 23 - Xantech Limited Warranty (Effective for products sold after July 1, 2006) Xantech Corporation (“Xantech”) warrants to the holder of a v

- 24 - Specifications Sampling Frequency 48kHz Audio Resolution 24 Bit, Stereo Output Power 30 Watts Per Channel THD + Noise Full Scale 0.

- 3 - Damage Requiring Service — These appliances should be serviced by qualified service personnel when: • A power supply connection or a plug

- 4 - 1.0 Introduction Exceptional Performance The D5KP is Xantech’s Amplified OLED Controller for the D5SH, D5SH4, D5RH, and D5XH Digital Audi

- 5 - Defining Terms Zone A Zone is defined as an area of the house that has separate source selection capabilities from all other areas of the

- 6 - Pre-Wiring D5RH and D5SH, D5SH4 Digital Audio Distribution Hub to D5KP Amplifier Keypad The D5SH4 and all associated components are wired

- 7 - D5IP Local Sources to the D5KP Amplifier Keypad Local sources are only available within the area that they are installed. They will not b

- 8 - D5KP - FRONT Figure 2.1: Front of D5KP Keypad ITEM DESCRIPTION 1 OLED Screen 2 SOURCE Selection 3 VOLUME Selection 4 MUTE Button 5 IR

- 9 - D5KP - REAR L+L-R+R-+-41523 Figure 2.2: Front of D5KP Keypad ITEM DESCRIPTION 1 SYSTEM RJ-45 Port 2 Speaker Output Connector 3 AUX